Stainless Steel Spiral Bevel Gear
Spiral Bevel Gears in Stainless Steel for Food, Pharmaceutical, Chemical, Marine and Water-Treatment Drives, Made to Drawing or Sample.

Specifications
| Material | Stainless steel to your grade, e.g. 304, 316, 410, 420, 17-4 PH |
|---|---|
| Gear Type | Spiral bevel gear and pinion |
| Maximum Gear Diameter | Up to 1200 mm |
| Module Range | Module 1 to 25 |
| Maximum Face Width | Up to 150 mm |
| Quantities | One-off replacement to repeat batches |
| From a Sample | Yes, reverse engineering available |
When a Spiral Bevel Gear Needs to Be Stainless
Case-hardened alloy steel is the normal choice for spiral bevel gears because it gives the hardest, most wear-resistant tooth. It also rusts. Where a drive is washed down, runs near seawater or chemicals, or must not contaminate a product, stainless steel is often specified instead, even though it carries less load than a carburised gear of the same size.
Typical drives that call for stainless spiral bevel gears:
- Mixers, agitators and blenders in food, dairy and pharmaceutical plants
- Packaging, filling and bottling machinery that is washed down daily
- Deck equipment, thrusters and pumps in marine service
- Chemical process equipment and water and effluent treatment drives
Choosing the Grade
The grade decides the balance between corrosion resistance and strength. Austenitic grades such as 304 and 316 resist corrosion best but cannot be hardened by heat treatment, so they suit lighter, slower drives. Martensitic and precipitation-hardening grades such as 410, 420 and 17-4 PH can be hardened for more load capacity, with somewhat lower corrosion resistance. We make the gear in the grade on your drawing; if the drawing leaves it open, tell us the environment, speed and load and we will discuss the options with you.
Why Spiral Rather Than Straight Teeth
Spiral teeth share the load across more than one tooth at a time. That matters more in stainless steel than in hardened alloy steel, because the material has less surface strength to spare. A spiral bevel set also runs more quietly, which helps in food and pharmaceutical plants where machines run close to operators.
What We Make
- Stainless steel spiral bevel gear and pinion sets, supplied as matched pairs
- Sizes up to 1200 mm diameter, module 1 to 25, face width up to 150 mm
- Single replacements copied from a worn sample, and repeat batches to drawing
Tooth cutting and lapping are done in-house, and each pair is checked for contact pattern and backlash before dispatch. For gears that do not need stainless steel, see our standard spiral bevel gears; for straight-tooth stainless gears, see stainless steel bevel gears.
Frequently Asked Questions
Are stainless steel spiral bevel gears as strong as alloy steel gears?
No. A case-hardened alloy steel gear carries more load for the same size. Stainless steel is chosen for corrosion resistance or hygiene; the gear size or grade is then chosen to suit the load.
Which stainless steel grade should I choose?
It depends on the environment and the load. 304 and 316 resist corrosion best; 410, 420 and 17-4 PH can be hardened for more strength. Tell us the application and we will discuss the choice.
Can you copy a worn stainless steel gear?
Yes. Send the gear and its mating pinion if possible, with the machine details, and we will make a matched replacement pair.
Should the pinion be stainless too?
Usually both members are in the same grade so they behave the same in service. In some drives a different grade is used for the pinion; we follow your drawing.
Related Products
Spiral Bevel Gear
Custom Spiral Bevel Gears and Matched Gear-and-Pinion Sets Up to 1200 mm Diameter and Module 25, Cut.
View details →Bevel Gear
Straight, Spiral, Zerol, Hypoid and Miter Bevel Gears Made to Drawing, Sample or Application Data, Up to 1200 mm Diameter.
View details →Straight Bevel Gear
Straight Bevel Gears for Slower Right-Angle Drives, Valves, Hand-Operated Machinery and Simple Gearboxes.
View details →Request a Quote for Stainless Steel Spiral Bevel Gear
Share your drawing, sample details, quantity and delivery location. Our engineering team will review it and reply.