Spiral Bevel Gear
Custom Spiral Bevel Gears and Matched Gear-and-Pinion Sets Up to 1200 mm Diameter and Module 25, Cut, Lapped and Ground In-House at Our Works in Gujarat.

Specifications
| Business Established | 2015 |
|---|---|
| Nature | Manufacturing |
| Maximum Gear Diameter | Up to 1200 mm |
| Module Range | Module 1 to 25 |
| Maximum Face Width | Up to 150 mm |
| Ratios | As per drawing and requirement |
| Cutting, Lapping and Grinding | Available in-house under one roof |
| Accuracy References | DIN, AGMA and customer-specific requirements |
| Quantities | Prototype through production |
| Reverse Engineering | Available |
What a Spiral Bevel Gear Does
A spiral bevel gear pair transmits power between two shafts that meet at an angle, usually 90°. The teeth are curved and set at an angle to the gear axis, so each tooth engages gradually from one end to the other and more than one tooth pair is in contact at any moment. Compared with a straight bevel pair of the same size, a spiral bevel pair runs more quietly, carries more torque and tolerates higher speed.
That is why spiral bevel gears are the usual choice for right-angle gearboxes, crushers, mixers, conveyor heads and machine-tool drives.
What We Manufacture
Agni Engineering has made spiral bevel gears since 2015 and has completed more than 500 projects, about 70% of them for export. We work to your drawing, to a worn sample, or to application data:
- Size: up to 1200 mm diameter, module 1 to 25, face width up to 150 mm
- Finish: cut, lapped or ground, all in-house
- Supply: single gears, pinions or matched sets, from one prototype to series production
By finish, see ground spiral bevel gears and hardened spiral bevel gears. For a gear copied from a worn sample, see reverse engineering.
Points That Decide a Good Spiral Bevel Set
- Hand of spiral and rotation. The hand of the pinion and the direction of rotation decide whether the axial thrust pushes the pinion into or out of mesh. Bearings must be chosen for that thrust.
- Mounting distance. Spiral bevel sets are sensitive to the axial position of both members. The mounting distance on the drawing must be held in the gearbox.
- Matched pair. Gear and pinion are finished and checked together. Replace them as a set.
- Contact pattern and backlash. Both are set at assembly and recorded, so the set runs the way it was tested.
Spiral or Straight Bevel?
Spiral bevel gears are the better choice above moderate speed, under shock load, or where noise matters. Straight bevel gears remain a sensible, lower-cost option for slow, lightly loaded drives. Our guide to spiral and straight bevel gears compares them in detail.
Frequently Asked Questions
What is the largest spiral bevel gear you can make?
Up to 1200 mm diameter, module up to 25 and face width up to 150 mm. For anything near these limits, send the drawing so we can confirm the blank, cutting and finishing route.
Do you supply the gear alone, without the pinion?
We can, after checking the existing pinion. A new gear running against a worn pinion rarely gives a good contact pattern, so we normally recommend replacing both as a matched set.
Which accuracy standard do you work to?
To the class stated on your drawing, under DIN, AGMA or ISO bevel gear standards, or to your own acceptance criteria.
Can you make spiral bevel gears from a sample?
Yes. Send both mating parts if possible, with the machine details. See replacement spiral bevel gears.
Related Products
Bevel Gear
Straight, Spiral, Zerol, Hypoid and Miter Bevel Gears Made to Drawing, Sample or Application Data, Up to 1200 mm Diameter.
View details →Straight Bevel Gear
Straight Bevel Gears for Slower Right-Angle Drives, Valves, Hand-Operated Machinery and Simple Gearboxes.
View details →Crown Wheel and Pinion
Crown Wheel and Pinion Sets for Industrial Drives, Made as Matched Spiral Bevel Pairs.
View details →Request a Quote for Spiral Bevel Gear
Share your drawing, sample details, quantity and delivery location. Our engineering team will review it and reply.